![]() |
![]() |
Revised December 15, 2007
Oil Cooling System
Air Cooled Engines Through 1983
Click on letters to go directly to part description
Models Through 1970 (Non-Doghouse Style Cooler)
A. 111-117-021E Oil Cooler, New $120.00
NOTE: Must use seal kit 111-198-029 when mounting this cooler on single relief case through 1969. On 1970 models, use seal 021-117-151A.
B. 111-117-151 Seal, Oil Cooler Through 1969 (2 Required) $0.25 each
NOTE: Use only if using original cooler on single relief case through 1969. On 1970 models use seal kit 111-198-029 if using original cooler,
C. N 12226.2 Spring Lock Washer, 6mm (2 Required) $0.06 each
D. N 11006.8 6mm Nut (2 Required) $0.10 each
Click on letters to go directly to part description
1971 Models Only (Doghouse Style Cooler)
E. 113-117-021 Oil Cooler, New $77.75
E. 113-117-021X Oil Cooler, Rebuilt $63.40
F. 021-117-151A Seal, Oil Cooler to Stand (2 Required) and Stand to Case (2 Required) $0.50 each
G. 113-117-301 Oil Cooler Stand, New $27.20
NOTE: If mounting the oil cooler stand to a single relief case (through 1969), use seal kit 111-198-029
H. N 11524.4 6mm Flat Washer (3 Required) $0.15
I. N 12226.2 6mm Spring Lock Washer (3 Required) $0.06
J. N 11006.8 6mm Nut (3 Required) $0.10
NOTE: Items H, I & J are required to mount cooler to stand.
- N 12228.2 8mm Spring Lock Washer (3 Required) $0.20
- N 11008.2 8mm Nut (3 Required) $0.10
NOTE: Items above are required to mount cooler stand to case.
K. 113-117-321U Oil Cooler Sealing Frame, Used CALL
Click on letters to go directly to part description
1972 Through 1983 Models (1700, 1800, 2000)
L. 021-117-021B Oil Cooler, New $196.40
- 021-117-021BX Oil Cooler, Reconditioned $63.00
- 021-117-151A Oil Cooler Seal (2 Required) $0.50 each
N. 021-117-171AU Clip Support for Oil Cooler, Used CALL
O. 021-117-181U Clip Support for Oil Cooler, Used CALL
P. N 12226.2 6mm Spring Lock Washer $0.06
Q. N 10715.2 Screw, 6X15 $0.25
R. 11525.2 8mm Flat Washer $0.10
S. N 12228.2 8mm Spring Lock Washer $0.20
- N 11524.4 6mm Flat Washer $0.05
- N 12226.2 6mm Spring Lock Washer $0.06
- N 11006.8 6mm Nut $0.10
NOTE: The above 3 items are required to mount cooler to case studs (3 each required).
What is the 111-198-029 Seal Kit?
Volkswagen engine cases through 1969 came with small oil galleries and single relief oil systems. The original oil coolers installed on these engines used the 111-117-151 seal shown in the listings above. With the introduction of the dual relief cases in 1970, the oil galleries where enlarged and a stepped seal was introduced to install the small hole oil cooler onto the large hole case. As time went on, Volkswagen eventually upgraded the replacement cooler with the larger holes, but now it required the same stepped seal to install it to the early small hole case. Seal kit 111-198-029 comes with two of these stepped seals and they must be installed as shown below to prevent leaks. The same applies when retro fitting a Doghouse style cooler to an early small hole case. How do you determine if you have a small hole case? Check the engine number. Bug B5 000 000 cases, Bus B6 000 000 and all engines beginning with 2 letters (AB, AE, AH, etc.) are usually dual relief, big hole cases. All others are usually single relief, small hole cases.
111-198-029 $1.85 pair
Single Relief Cases |
Dual Relief Cases |
This side is to the cooler (111-117-021E Replacement) or to Doghouse cooler stand. |
This side is to the original oil cooler (small hole). |
|
|
This side is to the the case (small hole). |
This side is to the case (large hole). |
Back To Home Page | Back To Online Catalog | Back To The Top | Email Us
Order Toll Free (800)792-2697 | Information (530)244-1616 | 24 Hour Fax (530)244-0933